欢迎光临厦门兴锐嘉进出口有限公司官网!
工控设备卡件 | 工业自动化主营:PLC系统 DCS系统 伺服系统 机器人系统
全国咨询热线:15359273791
您的位置: 首页>>产品展示 >
产品展示 》 EPRO 模块 》 PR9270V-EX 速度传感器

PR9270V-EX 速度传感器

型号:PR9270V-EX

联系人:刘经理
公司名称:厦门兴锐嘉进出口有限公司
公司地址:厦门市翔安区新澳路510号海峡现代城A座6楼609室
手机:15359273791
QQ:2851759119
邮箱:sales1@xrjdcs.com

PR9270V-EX 速度传感器
PR9270V-EX 速度传感器

我们这里有您急需的停产备件,

询不到的,买不到的,请联系我们!

欢迎来电询价,我们将会给您满意的!

公司主营进口PLC模块,可编程控制器,伺服控制系统,和DCS备件等,例如:ABB、AB、GE, Bently,FOXBORO. MOTOROLA.XYCOM.HONEYWELL.YASKAWA. SIEMENS. SCHNEIDER. REXROTH. YOKOGAWA .KUKA .OVATION .OMRON 等。尊敬的顾客您好,为了更好的保障您的合法权益,购买前请仔细阅读以下内容:

1.由于市场波动频繁,本店所标,并非实价,请买家提前咨询后再拍,感谢支持!

2,本店所售商品均为,图片实物拍摄。分为原装、无包装,工程余货和二手四种货品。购买前请联系客服仔细核对货品、型号、数量。3, 本店所售商品质量,无包装和二手商品签收三日质量出现问题均包退换,请放心购买。因买家自己弄错产品型号、参数或剪脚、上机、错误接入电源、错误安装、保管不当、人为损坏等除外。4,本店所售商品国内顺丰包邮,国外运费自理。支持七天内有任何产品质量问题退换货,过期一切损失请自行承担。签收快件前,请先检查包裹内货物是否有:破损、缺少、货物型号和数量不对等,有问题请拒绝签收并及时与我们联系。签收后,一切损失请自行承担。

5,说明 并非原价,以询价为准。

 

2. Common fault handling of IPC in broadcast transmitter

2.1 COM port communication is not normal

Fault phenomenon: when communicating with other COM port equipment RS-485, it can not be sent or received, or it can not be sent, etc.

Fault analysis: Usually, when programming COM communication, it is necessary to judge the communication state of COM port in advance. Make sure that you can send data when it's valid and receive data when it's valid. This is called RTS communication. However, in order to facilitate programming and speed up program execution, some users did not confirm the COM port communication state before designing the hardware, and did not pay attention to the query transceiver state during programming, which is also called AUTO communication mode. Considering its versatility, usually the motherboard with COM port is RTS communication, so when used for RS-485 communication, there will be a can send can not receive or can not receive the fault phenomenon;

Solution: The simplest solution to this problem is to use the EVOC product Ark-14520 (RS232 to RS485 module). However, if it is the communication between the COM port on the motherboard, usually there will be no such problem.

2.2 LCD display is not bright

Fault phenomenon: when the case on power, LCD display without any response;

Failure analysis: the direct cause of this failure is that the LCD backlight is not lit. After the maintenance personnel used a multimeter to measure the input power supply voltage of the backlight drive panel inverter, they found that +12V was not input. When the input power supply of the backlight drive panel was cut off, the voltage was normal. It is judged that the fault is caused by short circuit of +12V power supply on the backlight drive plate.

Solution: remove the backlight drive plate with short circuit problem from the chassis, and then power it on, so that the problem can be effectively solved. If necessary, some protective measures should be taken for the backlight drive panel to avoid such problems again.

更多相关库存型号:

EPRO   传感器及前置器    PR6423/017-010+CON021   

EPRO   TSI振动传感器 PR6423/003-030+CON021   

EPRO   传感器 PR6423/004-111+CON031   

EPRO   前置器 CON021

EPRO   传感器 PR6424/000-030   

epro   传感器 PR6424/000-030   

epro   前置器 CON021/914

EPRO   位移传感器 PR6424/010-140   

EPRO   前置器 CON021

EPRO   转速传感器 PR6423/002-001    

EPRO   传感器+前置器 PR6424/000-030+CON021/914

EPRO   传感器+前置器 PR6423/00R-111+CON031   

EPRO   传感器+前置器 PR6424/000-130+CON021   

EPRO   传感器+前置器 PR6423/003-130+CON021   

EPRO   传感器+前置器 PR6423/004-110+CON021   

epro   传感器+前置器 PR6423/010-040+CON021   

epro   传感器+前置器 PR6424/006-131+CON031   

epro   传感器+前置器 PR6423/10R-131+CON031   

epro   传感器+前置器 PR6423/010-010+CON021   

在线客服
联系方式

热线电话

15359273791

上班时间

周一到周五

公司电话

15359273791

二维码
线