MMS6110
MMS6110
现货特供
———————厦门兴锐嘉进出口有限公司————————
*国外直接采购，正品行货，价格优惠，售后保修，型号齐全，优势库存。
*所有备件的质保期均为1年，经过专业测试认证。
*如果您需要订购产品超过1件，请与我们联系，我们可以为您提供折扣。
*我们仅采用顺丰快递方式递送备件。
*如果您发现其他供货商为相同产品提供更为低廉的价格，我们也愿意参照其价格向您提供进一步的折扣。
如果还有其他任何问题，请随时与我们联系。
*请让我们知道您有任何，备品，备件的需要，我们可以给您进一步的援助，我们等候您的询盘。
*兴锐嘉做到信誉，信任，信服。
*一样的产品，不一样的是价格与服务。
*您的选择，就是我们的前进的动力。
下面是我公司的优势产品(日常用的多的,还有不常用的未列出，但都有做的)欢迎您的咨询！
品牌：EPRO
型号：
MMS6110
CON021
PR6423/010-010-CN
UES815S-24A
UES815S-24AR
SDM010
RSM020
USE815S
MMS6220
MMS6312
MMS6120
PR6423/000-000
At present, there are only four parameters of the product, namely module 485 address, communication baud rate, protocol selection and sampling rate. Therefore, this part mainly explains the setting and recovery process for these four parameters. The default 485 address of the product: 170, communication baud rate: 9600, protocol selection: the company's custom character protocol, sampling rate selection: low speed 10SPS. The following steps are illustrated by taking the 485 address, communication baud rate, protocol selection and sampling rate selection of the product as factory default parameters: 1) Connect the appropriate power according to parameter description and panel identification; 2) The 485 port of the product is connected with the RS232 port of the computer using the 485-232 module. If the computer does not have an RS232 interface, a USB to RS232 device is needed. 3) Use the conductor to shorten the SET and GND pins for 5 seconds and let the module enter the parameter modification state; 4) Open the attached serial debugging assistant software Commix, select ASCII mode, baud rate is 9600, data bit is 8, check bit N is none, stop bit 1. Enter the command: $AA2\CR, and then send it. If the return is correct, it means that the communication is correct. If there is no return, check whether the serial port selection, software Settings, USB to RS232, and 485 to 232 modules work normally, until the communication can be correct. 5) Set relevant parameters according to the NNTTCCFF\CR instruction. 6) Power on again, and the above parameters are the modified parameters. 7) After the successful modification, the parameters will not be lost if power is lost. The product can be directly connected to the corresponding network; Steps to restore factory parameters: 1) Disconnect the power supply; 2) Short connect SET and GND pins with the conductor, never relax or shake; 3) Power the product, disconnect the conductor of SET and GND pin after 5 seconds, and then the 485 address, communication baud rate, protocol selection and sampling rate selection of the product have been restored to the default factory parameters. 1. Connect all kinds of signal wires according to the interface description. 2. Select the DC power supply with voltage range of 10-30V and output current capacity of not less than 300mA to connect to the power port of the module; If the power indicator is on, it indicates that the power input is normal. Otherwise, the power should be unplugged immediately, and the power should be switched on after checking whether the power supply or module is normal. 3. Open the attached serial debugging assistant software Commix, and test each function according to the protocol selection and corresponding instructions. 1. Users can use configuration software to access operation modules. Of course, users can also write upper computer programs according to their specific applications. 2. Two protocols can be adopted to develop upper computer programs to operate the product. First, our custom character protocol is easy to remember and recognize, but the access efficiency is lower than the standard MODBUS_RTU protocol. The second is the standard MODBUS_RTU protocol. At the beginning, you need to have some understanding of MODBUS_RTU protocol, and you may need to test it back and forth for several times before you can successfully verify the calculation. However, with this protocol, the access efficiency is relatively high. 3. If the first method is used for programming, the field introduction of all instructions shall refer to "SK5000 series Product Square control Character Instruction System Description". 4. If the second method is adopted for programming, the register address, opcode and description of all instructions shall refer to SK5000 series product standard MODBUS_RTU Protocol Description. 1. The maximum external size: 120mm*71mm*43mm(including the thickness of the fixed seat for the back guide). 2. Installation method: standard industrial guide bar installation or screw hole installation.
客服1